Exactly how to Install a Tub (Step By Step).
Exactly how to Install a Tub (Step By Step).
Blog Article
This great article in the next paragraphs involving A Step-by-Step Guide to Installing a Bathtub is immensely attention-grabbing. You should see for yourself.
Installing a bath tub isn't exactly rocket science, however it does call for strong plumbing, woodworking, as well as in some cases, tiling abilities. Changing an old bath tub with a brand-new one is also a moderately challenging job. If the old bathtub is conveniently obtainable, the task can relocate speedily; if you have to open up a wall surface to remove the old bathtub and also position the new bathtub, the job is a lot harder. In either instance, the job is within a house handyman's skills, although you will require an assistant to leave the old tub and also set in the brand-new one. See to it you have qualified yourself for the work as well as are comfortable attempting it. Rather than employing a specialist to take over a halfway-completed task, it is far better to think about employing one prior to you begin. Chances are you might require an expert plumber to make tube links.
This post will aid you install a brand-new tub in your bathroom if you have actually already acquired a new bathtub as well as do not need to change the plan of your previous water system pipes.
Your tools as well as material list must comprise the following:
Planning for the Setup
Firstly, the sustaining frame provided with the bath needs to be fitted (if needed) according to the supplier's directions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to ensure that if the faucet comes with a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the taps system to prevent stress on the bathtub.
Fit the versatile faucet ports to the bottom of both taps making use of 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make certain you utilize every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath should now be ready to be fitted in its last position.
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installation, after that the first thing you should do is detach the water. After doing so, turn on the faucets to drain pipes any water staying in the system. The procedure of removing the existing faucets can be fairly problematic because of the limited gain access to that is often the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the taps. Have a fabric all set for the continuing to be water that will come from the pipelines. As soon as the supply pipes have been eliminated, make use of the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single taps from transforming throughout this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any old sealing compound.
Before carrying on to fit the brand-new faucets, compare the pipe connections on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Mounting the Bathtub
Making use of both wooden boards under its feet, position the tub in the called for position. The wood boards are handy in evenly spreading the weight of the bathtub over the area of the boards rather than focusing all the weight onto 4 little factors.
The following objective is to make sure that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level as well as changing the feet on the tub up until the spirit level checks out level.
To set up taps, fit the bottom of the furthest flexible tap connector to the appropriate supply pipe by making a compression join; then do the same for the various other faucet.
Activate the water and also inspect all joints as well as new pipework for leaks and also tighten them if essential. Fill up the tub and additionally inspect the overflow outlet and the regular electrical outlet for leaks.
Finally, take care of the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as sealing around the bathtub needs to wait up until the bathtub has actually been utilized at least when as this will resolve it into its last setting.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will require a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end provides a link to the existing supply pipes.
If you need to fit a monobloc, after that you will require lowering couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin making certain that the washers are in location in between the faucet and the sink. Safeguard the tap in place with the supplier offered backnut. Once the faucet is securely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap connectors. The previous type needs to be linked to the faucet ends initially, tightening up only by hand. The supply pipelines can later be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the location where the bath fulfills the tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to crack an inflexible seal, causing the water to pass through the wall in between the bathroom as well as the tiling, bring about problems with wetness and feasible leakages to the ceiling below.
You can pick from a variety of coloured sealers to assimilate your fixtures and also fittings. They are offered in tubes and also cartridges, and can sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger void to fill, you can load it with spins of soaked paper or soft rope. Bear in mind to always fill up the bath tub with water before sealing, to permit the movement experienced when the tub remains in usage. The sealer can break fairly early if you do not take into consideration this movement prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise conveniently readily available on the market. It is recommended to fit the ceramic tiles making use of waterproof or waterproof sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you enjoyed our post on Installing A Bathtub. Thank you so much for taking the time to read our piece. Enjoyed reading our piece? Please share it. Help others check it out. I am grateful for your time. Visit us again soon.
Explore Now Report this page